服务热线：：
15303929722
联系GCGC黄金城官网
公司名称：：GCGC黄金城官网
电话：：0392-3388939
传真：：0392-3382020
联系人：：周经理
手机：：18803921757
联系人：：赵经理
手机：：15303929722
邮箱：：hebiqitian@163.com
单元地址：：河南省鹤壁市市辖区东杨工业园区香山路152号
微机灰熔点测定仪摄像头的调试步骤
服务热线：：
2025-12-17 来自: GCGC黄金城官网. 浏览次数:232
Ash melting point camera debugging
装置好摄像头后，，，摄像头距离灰熔点炉体的间距为150mm
After installing the camera, the distance between the camera and the ash melting point furnace body is 150mm
摄像头介绍
Camera Introduction
摄像头三个旋钮调整，，，早年到后作用别离是：：
The three knobs of the camera are adjusted, and their effects from front to back are:
调整画面巨细
Adjusting the screen size
调整画面明暗
Adjusting the brightness of the screen
调整画面清澈度
Adjusting the clarity of the screen
画面调整
Screen adjustment
设备起头后，，，温度达到900℃时弹出提醒。。不重点击对话框中的“知晓了”，，，这时起头调整摄像头。。把稳：：调整速度要快，，，设备到1000℃后系统会自动起头尝试，，，导致调整失效
After the device starts, a prompt will pop up when the temperature reaches 900 ℃. Don't click on "Got it" in the dialog box, then start adjusting the camera. Attention: The adjustment speed should be fast. After the device reaches 1000 ℃, the system will automatically start the experiment, causing the adjustment to fail
先调整画面焦距，，，就是摄像头zui内侧的旋钮，，，调整到样品边缘清澈即可。。如下图
First adjust the focal length of the image, which is the innermost knob of the camera, until the sample edge is clear. As shown in the following figure
而后用摄像头中央那个旋钮来调整画面的亮度，，，不能太亮也不能太暗。。如下图
Then use the knob in the middle of the camera to adjust the brightness of the image, which should not be too bright or too dark. As shown in the following figure
最后调整画面巨细，，，用摄像头zui外侧的，，，先将带编号的方框齐全框住样品，，，尖头部门不必要齐全顶住“编号方框”的顶部。。
Finally, adjust the picture size. Use the outermost part of the camera to completely frame the sample with the numbered box. The pointed part does not need to completely support the top of the "numbered box".
画面调整好之后点击弹出对话框中的“知晓了”
After adjusting the screen, click "Got it" in the pop-up dialog box
而后用鼠标点击界面中的“原型”画面。。
Then click on the "prototype" screen in the interface with the mouse.
点击过“原型”画面后，，，系统会固定目前的亮度，，，而后就算灰熔点测定仪摄像头调试结束
After clicking on the "prototype" screen, the system will fix the current brightness, and then even after debugging is completed
具体详情可联系鹤壁GCGC黄金城官网公司进行征询0392-3388939 3388929